Glossary entry (derived from question below)
English term or phrase:
Single-sided fitting/double-sided fitting
French translation:
Pose sur un seul côté / Pose sur deux côtés
Added to glossary by
Johannes Gleim
Nov 11, 2020 08:12
3 yrs ago
22 viewers *
English term
Single-sided fitting/double-sided fitting
English to French
Tech/Engineering
Electronics / Elect Eng
Raccordage
Bonjour à toutes et tous,
Pourriez-vous m'aider à mieux comprendre ?
STAGE 1
Drill a 3mm (approx.) pilot hole where the antenna is to be located.
- Single sided fitting
Drill a l9mm hole. Proceed to STAGE 2.
- Double sided fitting
Drill a l2mm hole. Fit the feeder assembly through the hole. Push the weather
seal over it. Place the base moulding over it. Screw on the base insert and
tighten firmly by hand.
Merci d'avance,
Gladis
Pourriez-vous m'aider à mieux comprendre ?
STAGE 1
Drill a 3mm (approx.) pilot hole where the antenna is to be located.
- Single sided fitting
Drill a l9mm hole. Proceed to STAGE 2.
- Double sided fitting
Drill a l2mm hole. Fit the feeder assembly through the hole. Push the weather
seal over it. Place the base moulding over it. Screw on the base insert and
tighten firmly by hand.
Merci d'avance,
Gladis
Proposed translations
(French)
4 | Pose sur un seul côté / Pose sur deux côtés | Johannes Gleim |
Change log
Nov 11, 2020 08:15: Gladis Audi, DipTrans changed "Restriction (Pairs)" from "none" to "working" , "Restriction (Native Lang)" from "none" to "fra" , "Restriction Fields" from "none" to "interest"
Nov 14, 2020 09:51: Johannes Gleim Created KOG entry
Proposed translations
7 hrs
Selected
Pose sur un seul côté / Pose sur deux côtés
I understand that the complete device is mounted onto one wall side, or the device is split and two parts of the device are mounted onto each wall side and connected by wiring put through the 12-mm-hole.
Proposition :
- Single sided fitting
Drill a 19mm hole. Proceed to STAGE 2.
- Double sided fitting
Drill a 12mm hole. Fit the feeder assembly through the hole.
=>
- Pose sur un seul côté
Percez un trou de 19 mm. Passez à l'étape 2.
- Pose sur deux côtés
Percez un trou de 12 mm. Installez l'assemblage d'alimentation dans le trou.
--------------------------------------------------
Note added at 1 day 2 hrs (2020-11-12 10:46:31 GMT)
--------------------------------------------------
Unfortunately we do not know what is described under "stage 2". Probably similar to "double side fitting".
I conclude from the context that for "single side fitting" the feeder assembly is screwed to the wall on the inside, and the base, weather seal and antenna on the outside.
--------------------------------------------------
Note added at 3 days 3 hrs (2020-11-14 11:19:59 GMT) Post-grading
--------------------------------------------------
The context has already been asked for translation to Spanish in 2007:
Drill a 3mm (approx.) pilot hole where the antenna is to be located. Clean away swarf with a light cloth. The antenna can be mounted on panels up to 3mm thick.
Having decided on cable routing, proceed to STAGE 1.
STAGE 1
a. Single sided fitting
Drill a l9mm hole. Proceed to STAGE 2.
b. Double sided fitting
Drill a l2mm hole. Fit the feeder assembly through the hole. Push the weather seal over it. Place the base moulding over it. Screw on the base insert and tighten firmly by hand. Proceed to STAGE 3.
STAGE 2
Install the feeder assembly through the hole, cable first. Hold the feeder assembly and centralise in the hole. Push the weather seal over it; this will hold the feeder assembly in position. Carefully place the base moulding over it. Screw on the base insert and tighten firmly by hand.
STAGE 3
Tighten up via the base insert using a small open spanner, 4Nm torque (3 foot pounds) maximum.
https://forum.wordreference.com/threads/single-sided-fitting...
Proposition :
- Single sided fitting
Drill a 19mm hole. Proceed to STAGE 2.
- Double sided fitting
Drill a 12mm hole. Fit the feeder assembly through the hole.
=>
- Pose sur un seul côté
Percez un trou de 19 mm. Passez à l'étape 2.
- Pose sur deux côtés
Percez un trou de 12 mm. Installez l'assemblage d'alimentation dans le trou.
--------------------------------------------------
Note added at 1 day 2 hrs (2020-11-12 10:46:31 GMT)
--------------------------------------------------
Unfortunately we do not know what is described under "stage 2". Probably similar to "double side fitting".
I conclude from the context that for "single side fitting" the feeder assembly is screwed to the wall on the inside, and the base, weather seal and antenna on the outside.
--------------------------------------------------
Note added at 3 days 3 hrs (2020-11-14 11:19:59 GMT) Post-grading
--------------------------------------------------
The context has already been asked for translation to Spanish in 2007:
Drill a 3mm (approx.) pilot hole where the antenna is to be located. Clean away swarf with a light cloth. The antenna can be mounted on panels up to 3mm thick.
Having decided on cable routing, proceed to STAGE 1.
STAGE 1
a. Single sided fitting
Drill a l9mm hole. Proceed to STAGE 2.
b. Double sided fitting
Drill a l2mm hole. Fit the feeder assembly through the hole. Push the weather seal over it. Place the base moulding over it. Screw on the base insert and tighten firmly by hand. Proceed to STAGE 3.
STAGE 2
Install the feeder assembly through the hole, cable first. Hold the feeder assembly and centralise in the hole. Push the weather seal over it; this will hold the feeder assembly in position. Carefully place the base moulding over it. Screw on the base insert and tighten firmly by hand.
STAGE 3
Tighten up via the base insert using a small open spanner, 4Nm torque (3 foot pounds) maximum.
https://forum.wordreference.com/threads/single-sided-fitting...
Peer comment(s):
neutral |
Tony M
: I don't think this is about fitting it TO both sides of the panel; rather, the expression would be used in EN to describe the situation where you have / do not have access to both sides for working. / The EN usage seems quite clear and unambiguous to me.
44 mins
|
All depends on the further context I've requested and the ambience (e.g. scyscrapers may not allow outside mounting)
|
4 KudoZ points awarded for this answer.
Discussion
STAGE 4
Fit the rod assembly. Position it as desired and tighten the set screws firmly.
Johannes, lisez la discussion du lien publié. Le texte complet s'y trouve.
https://www.proz.com/kudoz/english-to-french/engineering-gen...
Or je vois qu'on peut répondre tout en étant de langue maternelle allemande et moins fluide en français que Tony et moi. C'est un bug ou quoi ?
Enfin, moi je traduirais par qqc comme "montage passe-cloison" pour double-sided.
- the kind of device and its purpose?
- the type of antenna and data emitted or received?
- the kind of wall or panel?
- the kind of wiring or cabling?
- what parts can de mounted on the inner side and which on the outer side?
- the mounting type of the device parts?
'Fitting here definitely refers to the action of fitting (generally 'pose'), rather than to the physical object 'a fitting' (raccord, appareil, etc.)